BEST-121體積表面電阻率測試儀

體積表面電阻率測試儀符合標準：
GB1410《固體電工絕緣材料絕緣電阻、體積電阻系數和表面電阻試驗方法》 
ASTM D257《絕緣材料的直流電阻或電導試驗方法》 
 
體積表面電阻率測試儀概述： 
  本儀器既可測量高電阻，又可測微電流。采用了美國Intel公司的大規模集成電路,使儀器體積小、重量輕、準確度高。以雙3.1/2 位數字直接顯示電阻的高阻計和電流。量限從1×104Ω ～1×1018 Ω，是目前國內測量范圍最寬，準確度最高的數字超高阻測量?jī)x。電流測量范圍為2×10-4 ～1×10-16Ａ。機內測試電壓為10/50/100/250/500/1000V任意可調。體積表面電阻率具有精度高、顯示迅速、性好穩定、讀數方便， 適用于防靜電產品如防靜電鞋、防靜電塑料橡膠制品、計算機房防靜電活動地板等電阻值的檢驗以及絕緣材料和電子電器產品的絕緣電阻測量。 

體積表面電阻率測試儀技術指標： 
1、電阻測量范圍： 1×104Ω ～1×1018Ω。 
2、電流測量范圍為： 2×10-4A～1×10-16A 
3、雙表頭顯示： 3.1/2位LED顯示 
4、內置測試電壓：10V、50V、100V、250、500、1000V 
5、基本準確度：1% (*注) 
6、使用環境： 溫度：0℃～40℃，相對濕度<80% 
7、機內測試電壓： 10/50/100/250/500/1000V 任意切換 
8、供電形式： AC 220V，50HZ，功耗約5W 
9、儀器尺寸： 285ｍｍ× 245ｍｍ× 120 mm 
10、質量： 約2.5KG 

體積表面電阻率測試儀工作原理： 
    根據歐姆定律，被測電阻Rx等于施加電壓V除以通過的電流I。傳統的高阻計的工作原理是測量電壓V固定，通過測量流過取樣電阻的電流I來得到電阻值。從歐姆定律可以看出，由于電流I是與電阻成反比，而不是成正比，所以電阻的顯示值是非線性的，即電阻無窮大時，電流為零，即表頭的零位處是∞，其附近的刻度非常密，分辨率很低。整個刻度是非線性的。又由于測量不同的電阻時，其電壓V也會有些變化，所以普通的高阻計是精度差、分辨率低。 
    本儀器是同時測出電阻兩端的電壓V和流過電阻的電流I，通過內部的大規模集成電路完成電壓除以電流的計算，然后把所得到的結果經過A/D轉換后以數字顯示出電阻值，即便是電阻兩端的電壓V和流過電阻的電流I是同時變化，其顯示的電阻值不象普通高阻計那樣因被測電壓V的變化或電流Ｉ的變化而變，所以，即使測量電壓、被測量電阻、電源電壓等發生變化對其結果影響不大，其測量精度很高(專利)，從理論上講其誤差可以做到零，而實際誤差可以做到千分之幾或萬分之幾。 

體積表面電阻率測試儀典型應用： 
1．測量防靜電鞋、導電鞋的電阻值 
2、測量防靜電材料的電阻及電阻率 
3、測量計算機房用活動地板的系統電阻值 
4、測量絕緣材料電阻(率) 
5、光電二極管暗電流測量 
6、物理,光學和材料研究 

體積表面電阻率測試儀標準配置： 
1、測試儀器：1臺 
2、電源線：1條 
3、測量線：3根（屏蔽線、測試接線、接地線） 
4、使用說明書：1份

體積表面電阻率測試儀使用方法： 
6.1接好電源線 
確保電源為220VAC/50Hz 
6.2接通電源 
   將電流電阻量程置于 104 檔,電壓量程置于10V，然后開機。
6.3調零 
在“Rx”兩端開路的情況下,調零使電流表的顯示為0000 .注意：在“Rx”兩端不開路，如接在電阻箱或被測量物體上時調零后測量會產生很大的誤差。一般一次調零后在測試過程中不需再調零。 完畢后關機。
6.4連接線路 
    接好測試線，將測試線將主機與屏蔽箱連接好，測體積電阻時測試按鈕撥到Rv邊，測表面電阻時測試按鈕撥到Rs邊。然后開機。
6.5選擇合適的測量電壓 
★電壓選擇開關在后面板，注意，在測試過程中不要隨意改動測量電壓，可能因電壓的過高或電流過大損壞被測試器件或測試儀器; 
6.6測試 
測量時從低檔位逐漸拔往高檔，每撥一次稍停留1～2秒以使觀察顯示數字， 當被測電阻大于儀器測量量程時，電阻表顯示“1”，此時應繼續將儀器撥到量程更高的位置，當測量?jī)x器有顯示值時應停下，當前的數字乘以檔次即是被測電阻值。當有顯示數字時不要再往更高次檔撥，否測儀器會過量程，機內保護電路開始工作，儀器測量準確度會下降。 
6.7 測試完畢將電阻電流量程拔至“104 ”檔，電壓量程調至10V后關閉電源
★每測量一次均應將量程開關撥回到104“調零”檔的量程位置以免開機或測量端短路時而損壞儀器。
6.8 測量電流及1015Ω以上超高電阻的測量應用測量電流后用歐姆定律以電壓除以電流計算電阻的方法，詳見8.5節內容。
6.9 體積電阻和表面電阻轉換
★在測試過程中，使用屏蔽箱在進行體積電阻和表面電阻轉換時，必須把電源關閉后進行檔位轉換，否則會導致電壓沖擊到主機無法顯示或損壞。

體積表面電阻率測試儀
Meet the standards:
GB1410 "test method for insulation resistance, volume resistance coefficient and surface resistance of solid electrical insulating materials"
Test method for DC resistance or conductance of insulating materials by D257 ASTM
Summary
The instrument can measure high resistance, and measuring current. Large scale integrated circuit of Intel company is adopted, which makes the instrument small size, light weight and high accuracy. High resistance meter and current with dual 3.1/2 bit digital direct display resistance. The measurement range is from 1 * 104 to 1 * 1018, which is the most wide measurement range and the highest accuracy. The current measurement range is 2 * 10-4 ~ 1 * 10-16A. The test voltage of the machine is adjustable for 10/50/100/250/500/1000V. The surface volume resistivity has a high precision, rapid, good stability, easy reading for inspection to the anti electrostatic products such as anti-static shoes, anti electrostatic plastic and rubber products, computer room anti static floor resistance value and insulating materials electrical and electronic products insulation resistance measurement.
Technical index:
1, resistance measurement range: 1 * 104 ~ 1 * 1018.
2, the current measurement range is: 2 x 10-4A ~ 1 x 10-16A
3, double headers: 3.1/2 LED display
4, built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V
5, basic accuracy: 1% (* Note)
6, the use of the environment: temperature: 0 degrees Celsius to 40 degrees Celsius, the relative humidity of <80%
7, the machine test voltage: 10/50/100/250/500/1000V arbitrary switching
8, power supply form: 220V AC, 50HZ, power consumption of about 5W
9, instrument size: 285mm * 245mm * 120 mm
10, quality: about 2.5KG
Working principle
According to Ohm's law, the measured resistance Rx is equal to the applied voltage V divided by the current I. The traditional high resistance meter works is the measurement of the voltage V fixed, by measuring the flow through the sampling resistance of the current I to get the resistance value. Can be seen from Ohm's law, due to the current I is inversely proportional to the resistance, and not directly proportional to, so the resistance to the display value is nonlinear, the resistance is infinite, the current is zero, namely header zero is infinity, near the scale is very close, the resolution is too low. The whole scale is nonlinear. And since the measurement of different resistance, the voltage V will be some changes, so the average high resistance meter is poor accuracy, low resolution.
This instrument is the current flowing through the resistor V and the voltage across the resistor I measured at the same time, the large scale integrated circuit to complete the calculation of the internal voltage divided by the current, and then the results obtained after A/D conversion by the digital display of the resistance value, even if the current voltage V and the flow resistance of the two ends of the I is changed at the same time, the resistance value is not displayed as ordinary high resistance meter as a result of changes in the measured voltage or current change of V and I, so even if the measurement voltage, the measured resistance and power voltage change has little influence on the results, the measuring accuracy is very high (patent), according to the theory of the error can do zero, while the actual error can be done a few thousandths or very few.
Typical applications:
1 measure the resistance value of the anti-static shoes and conductive shoes.
2. Measure the resistance and resistivity of the antistatic material.
3. Measure the system resistance value of the computer room floor.
4, measuring the resistance of insulating materials (rate)
5, photoelectric diode dark current measurement
6, physics, optics and materials research
Standard configuration:
1, test equipment: 1 sets
2, power line: 1
3, measuring line: 3 (shielding wire, test wiring, grounding wire)
4, the instruction manual: 1 copies
Using method:
6.1 connect the power cord.
Make sure the power supply is 220VAC/50Hz
6.2 power on
The current resistance range in 104 stalls, the voltage range of 10V, and then boot.
6.3 zero adjustment
In the open at both ends of the Rx, zero to ammeter display 0000. Note: at both ends of the "RX" does not open, such as connected to the resistor or measured object tune zero measurement will produce great error. Generally after a zero adjustment in the test process does not need to adjust the zero. After shutdown.
6.4 link line
Connect the test line, the test line will be connected to the host and the shield box, the measurement of the volume resistance when the test button dial to the Rv side, the test surface resistance when the test button to dial the Rs edge. Then boot.
6.5 select the appropriate measurement voltage
9:28 voltage selector switch on the rear panel, pay attention to, in the testing process do not arbitrarily change the voltage measurement may due to excessive voltage or current too damaged device under test or test instrument.
6.6 test
Measurements from low-grade gradually pulling to high-grade, each allocated a slightly stay 1 ~ 2 seconds to enable observation of the digital display, when more than the range of measurement instrument measured resistance, resistance meter display "1", at this time, should continue to be instrument dials to range higher position, when the measurement apparatus with display value should be stopped, the number is multiplied by the grade is measured resistance values. When there is a display of the number, do not go to a higher level, no measuring instrument will be over range, the machine within the protection circuit to work, the accuracy of the instrument measurement will drop.
6.7 after the test resistor current range to pull "104", voltage range to 10V after power off
* measured every one shall be the range switch dial back the 104 "zero" gear range position so as not to boot or measurement shorted sometimes damage the instrument.
6.8 measurement of the current and the measurement of more than 1015 of the ultra high resistance measurement of the current use of the Ohm's law in order to voltage divided by the current calculation of the resistance of the method, see the 8.5 section.
6.9 volume resistance and surface resistance conversion
] in the testing process, using shielding box in the volume resistance and surface resistance conversion must be the power off after the shift conversion, otherwise it will lead to the main impulse voltage

北廣精儀公司是一家專業從事檢測儀器，自動化設備生產的高新科技企業公司，
01066024083

“精細其表，精湛于內”是北廣精儀一慣秉承的原則。其先進的設計風格，卓越的制造技術和完善的服務體系，為科研機構、大專院校，企業和質量檢測機構提供一流的產品和優質的服務。北廣精儀公司集軟件設計、機械、力學、汽壓、電子、電機以及研發、品保、生管、檢測等專業人才，獲取即時資訊，發展領先的產品與服務。產品嚴格貫徹：ISO、AATCC、ASTM、DIN、EN、GB、BS、JIS、ANSI、UL、TAPPI、IEC、VDE等標準，廣泛適用于：科研單位、質檢機構、大專院校以及家具，紡織、玩具、橡膠、塑料、制鞋、皮革、包裝、航空等產業，為材料開發、物性試驗、教學研究、品質管理、進料檢驗等提供精準的數據。

北廣公司核心技術由北廣公司嚴格組建 并有專業的儀器美工專注外觀設計 從儀器的研發、生產、銷售、售后等 完全承建高新企業體系 。

并且研發更高端的試驗控制儀器 控制方式完全升級 現研發的微機控制儀器、控制方式采用無線藍牙首發技術 并且可選用 232 / USB/亞太局域網絡端口，已是全國頂尖 唯一


經營理念：
  一、誠信待戶 顧客至上      全心全意為顧客考慮，使顧客能切身感受到人性化的儀器。
  二、精準檢測 保質保量      精準檢測是我們的責任 保質保量是我們對客戶的鄭重承諾
  三、技術領先 創新理念    儲備一流的開發人才，引進世界領先技術，采用先進的設計理念，打造最精良的檢測儀器。 

北廣產品廣泛應用于國防、大專院校以及檢測所等行業，本公司以技術的創新為企業的發展方向，以新型實用的產品引導客戶的需求

北廣公司所供產品嚴格按照國家標準生產制造，嚴謹?shù)闹圃飙h(huán)節確保每一臺出廠儀器質量和性能的卓越，服務優質，質優價廉